quill chuck - traducción al ruso
Diclib.com
Diccionario ChatGPT
Ingrese una palabra o frase en cualquier idioma 👆
Idioma:

Traducción y análisis de palabras por inteligencia artificial ChatGPT

En esta página puede obtener un análisis detallado de una palabra o frase, producido utilizando la mejor tecnología de inteligencia artificial hasta la fecha:

  • cómo se usa la palabra
  • frecuencia de uso
  • se utiliza con más frecuencia en el habla oral o escrita
  • opciones de traducción
  • ejemplos de uso (varias frases con traducción)
  • etimología

quill chuck - traducción al ruso

IRISH PROGRESSIVE DEMOCRATS POLITICIAN
Mairin Quill; Máirin Quill

quill chuck      
цанговый патрон
three-jaw chuck         
  • Arthur Irving Jacobs (1858–1918)
  • drill shanks]] of a range of diameters. The end view shows the three small jaws that slide within the body.
  • Independent four-jaw chuck, with the jaws independently set. The key is used to adjust each jaw separately.
  • The Jacobs type chuck, with three converging splines or jaws, is perhaps the most usual design. This one is tightened with a key, but some types may be sufficiently tightened by hand
  • Chuck with six jaws
  • faceplate]]. The jaws are stepped on one side and full height for gripping on the other and are reversible.  Generally the jaws are usable for holding either outside as shown here, or inside as in gripping the inside of a pipe.
  • Two pin chucks. The top one is assembled, the lower one shows the body and nose cap assembled with the collet piece below it.
  • Diagram of an SDS chuck
  • Taper spindle nose with threaded retention. The retainer ring is wrenched with a spanner wrench.
  • Self-centering three-jaw chuck and key with one jaw removed and inverted showing the teeth that engage in the scroll plate. The scroll plate is rotated within the chuck body by the key, the scroll engages the teeth on the underside of the jaws which moves the three jaws in unison, to tighten or release the workpiece.
SPECIALIZED TYPE OF CLAMP TO HOLD A ROTATING TOOL OR WORKPIECE
Pin chuck; Four-jaw chuck; Three-jaw chuck; Scroll chuck; Independent-jaw chuck; Arthur I. Jacobs; Lathe chuck; Chuck key; Drill chuck; Tool chuck; Scroll plate; Self-centering chuck; Scroll gear; Special Direct System

нефтегазовая промышленность

трёхкулачковый патрон

патрон с тремя плашками

lathe chuck         
  • Arthur Irving Jacobs (1858–1918)
  • drill shanks]] of a range of diameters. The end view shows the three small jaws that slide within the body.
  • Independent four-jaw chuck, with the jaws independently set. The key is used to adjust each jaw separately.
  • The Jacobs type chuck, with three converging splines or jaws, is perhaps the most usual design. This one is tightened with a key, but some types may be sufficiently tightened by hand
  • Chuck with six jaws
  • faceplate]]. The jaws are stepped on one side and full height for gripping on the other and are reversible.  Generally the jaws are usable for holding either outside as shown here, or inside as in gripping the inside of a pipe.
  • Two pin chucks. The top one is assembled, the lower one shows the body and nose cap assembled with the collet piece below it.
  • Diagram of an SDS chuck
  • Taper spindle nose with threaded retention. The retainer ring is wrenched with a spanner wrench.
  • Self-centering three-jaw chuck and key with one jaw removed and inverted showing the teeth that engage in the scroll plate. The scroll plate is rotated within the chuck body by the key, the scroll engages the teeth on the underside of the jaws which moves the three jaws in unison, to tighten or release the workpiece.
SPECIALIZED TYPE OF CLAMP TO HOLD A ROTATING TOOL OR WORKPIECE
Pin chuck; Four-jaw chuck; Three-jaw chuck; Scroll chuck; Independent-jaw chuck; Arthur I. Jacobs; Lathe chuck; Chuck key; Drill chuck; Tool chuck; Scroll plate; Self-centering chuck; Scroll gear; Special Direct System

медицина

насадка для шлифмашины

Definición

Chuck
To throw something.
Just chuck the remote control over here, willya?

Wikipedia

Máirín Quill

Máirín Quill (born 15 September 1936) is a former Irish politician who served as a Senator from 1997 to 2002, after being nominated by the Taoiseach. She served as a Teachta Dála (TD) for the Cork North-Central constituency from 1987 to 1997.

A schoolteacher, Quill qualified as a primary school teacher from Mary Immaculate College, Limerick; she followed her teaching diploma by studying by night at University College Cork for a degree in English and History, and then a Higher Diploma in Education.

She was first elected to Dáil Éireann for the Cork North-Central constituency at the 1987 general election. She was one of 14 Progressive Democrat TDs resulting from that party's first general election. She had previously contested the Cork City constituency at the 1977 general election and Cork North-Central at the 1981 general election, each time as a Fianna Fáil candidate and each time losing.

Quill retained her seat in two successive general elections, but lost it at the 1997 general election to Billy Kelleher of Fianna Fáil. She was then nominated by the Taoiseach, Bertie Ahern, to the 21st Seanad. She did not contest the 2002 general election.

From 1979 until 2009, she was a member of Cork City Council, representing the North East ward. She did not contest the 2009 local elections.

¿Cómo se dice quill chuck en Ruso? Traducción de &#39quill chuck&#39 al Ruso